Rutgers 12-inch cyclotron magnet 

;modeling including all four quadrants re-typed after 
;a hard drive failure lost the original file in March 2005.
;
;NOTE: this is a slice down the middle of the magnet
;where the pole piece is widest (this really should be
;a 3-D problem, but hey, its fre....
;
;A hard copy of the original is located in CYC logbook 2
;page 176
;
; last modified 3/12/05 Sunday afternoon

&reg kprob=0,			;poisson or pandira problem
mode=-1				;Used fixed gamma for material 2
mat=2,
nbslo=0,			;Dirichlet boundary condition on lower edge
nbsup=0,			;Dirichlet boundary condition on upper edge
nbslf=0,			;Dirichlet boundary condition on left edge
nbsrt=0,			;Dirichlet boundary condition on right edge


;----this section for for variable density mesh--------------------- 
;	(all of it I think, it's been a while)

XMINF=0,XMAXF=0,YMINF=-3,YMAXF=3,KMIN=120,KTOP=240,LMIN=0,LTOP=0 ;

XREG1=-20,XREG2=20
kreg1=40,kreg2=181,kmax=221
yreg1=-10,yreg2=10
lreg1=40,lreg2=201,lmax=241 &

;-------------------------------------------------------------------

;&reg mat=2 & 
&po x=-53.25,y=-45.50 &	; Entire geometry is initially iron
&po x= 53.25,y=-45.50 &
&po x= 53.25,y= 45.50 &
&po x=-53.25,y= 45.50 &
&po x=-53.25,y=-45.50 &

&reg mat=1 &		; start of air region
&po x=-38.25,y=-30.50 &
&po x=-15.24,y=-30.50 &
&po x=-15.24,y= -5.08 &
&po x= 15.24,y= -5.08 &
&po x= 15.24,y=-30.50 &
&po x= 38.25,y=-30.50 &
&po x= 38.25,y= 30.50 &
&po x= 15.24,y= 30.50 &
&po x= 15.24,y=  5.08 &
&po x=-15.24,y=  5.08 &
&po x=-15.24,y= 30.50 &
&po x=-38.25,y= 30.50 &
&po x=-38.25,y=-30.50 &
 
&reg mat=1, cur=-30000&	;start of left-side bottom coil
&po x=-37.0,y=-14.26 &
&po x=-16.0,y=-14.26 &
&po x=-16.0,y=-29.50 &
&po x=-37.0,y=-29.50 &
&po x=-37.0,y=-14.26 & 

&reg mat=1, cur=+30000&	;start of right-side bottom coil
&po x= 37.0,y=-14.26 &
&po x= 16.0,y=-14.26 &
&po x= 16.0,y=-29.50 &
&po x= 37.0,y=-29.50 &
&po x= 37.0,y=-14.26 &

&reg mat=1, cur=-30000&	;start of left-side to coil
&po x=-37.0,y= 14.26 &
&po x=-16.0,y= 14.26 &
&po x=-16.0,y= 29.50 &
&po x=-37.0,y= 29.50 &
&po x=-37.0,y= 14.26 &

&reg mat=1, cur=+30000&	;start of left-side bottom coil
&po x= 37.0,y= 14.26 &
&po x= 16.0,y= 14.26 &
&po x= 16.0,y= 29.50 &
&po x= 37.0,y= 29.50 &
&po x= 37.0,y= 14.26 &

&reg mat=2 &		;start of top pole tip region
&po x=  0.000,y=  2.591 &
&po x= 12.700,y=  2.644 &
&po x= 14.138,y=  2.926 &
&po x= 14.854,y=  3.642 &
&po x= 15.240,y=  5.080 &
&po x=-15.250,y=  5.080 &
&po x=-14.854,y=  3.642 &
&po x=-14.138,y=  2.926 &
&po x=-12.700,y=  2.644 &
&po x=  0.000,y=  2.591 &


&reg mat=2 &		;start of bottom pole tip region
&po x=  0.000,y= -2.591 &
&po x= 12.700,y= -2.644 &
&po x= 14.138,y= -2.926 &
&po x= 14.854,y= -3.642 &
&po x= 15.240,y= -5.080 &
&po x=-15.250,y= -5.080 &
&po x=-14.854,y= -3.642 &
&po x=-14.138,y= -2.926 &
&po x=-12.700,y= -2.644 &
&po x=  0.000,y= -2.591 &